Epson Stylus 1500 Service Manual Download Page 101

Page: 101 / 185

Middle Frame Unit Removal

Remove the printer mechanism. (See page 3-9.)

Remove the carriage unit. (See page 3-22.)

Remove the paper eject frame unit. (See page 3-24.)

Remove the base frame. (See page 3-26.)

Remove the paper eject drive unit. (See page 3-27.)

Remove the paper feed roller unit. (See page 3-31.)

Remove 2 (CBS 3

6) screws securing the middle frame to the bottom frame and the

(CBS 3

6) screw securing the middle frame to the paper pickup guide frame.

Remove the middle frame unit by pulling it forward and then upward.

DISASSEMBLY/ASSEMBLY POINT

Assemble the middle frame unit so it fits the bottom frame completely.

CAUTION

❒

Do not place the cables between the sub frame and the bottom frame.

❒

Never touch the white PF gears. Handling them will cause damage or contamination that
will affect print quality.

CBS 3 x 6

Middle Frame Unit

Bo ttom Frame

ASF Tr ansmission Ratchet

Paper Pickup
Gu ide Fr ame

Figure 3-29. Removing the Middle Frame Unit

Disassembly and Assembly

3-32

EPSON Stylus 1500 Service Manual

Summary of Contents for Stylus 1500


























































































































































































Search results

Summary of Contents for Stylus 1500

Reviews:

Related manuals for Stylus 1500

Brands by name

Popular brands

Epson Stylus 1500, Service Manual

Search results

Summary of Contents for Stylus 1500

Reviews:

Related manuals for Stylus 1500

Brands by name

Popular brands