manualshive.com logo in svg

Epson SC-S40600 Series, User Manual

Share
Download
Epson SC-S40600 Series User Manual Download Page 76

D

Place the new ink supply unit into the tray and
lower the handle.

E

While the ink supply unit is in the tray, as shown
in the illustration below, carefully shake it by
tilting it up and down at about a 60 degree angle 5
times in 5 seconds.

In the case of OR, WH, or MS, shake it well
approx. 25 times in 25 seconds.

F

Match the color on the label on the ink supply
unit with the label on the ink unit, and then fully
insert the tray.

G

Move the lock switch to the left to lock it.

Repeat steps 2 to 7 to replace other ink supply
units.

c

Important:

Place ink supply units in all the trays, and then
insert them into the ink unit. Printing is not
possible if, for even one color, an ink supply
unit is not loaded into a tray or a tray is not
inserted into the ink unit.

Disposal

U

 

“Disposal” on page 84

Disposing of Waste Ink

Preparing and Replacement 
Timing

Prepare empty waste ink bottle. is displayed

Prepare a new Waste Ink Bottle as soon as possible.

When you want to replace the Waste Ink Bottle at this
stage due to night operations and so on, select 

Replace

Ink Bottle

 from the setup menu, and then replace the

bottle. If you perform the replacement without selecting

Replace Ink Bottle

, the waste ink counter will not

operate correctly.

Maintenance menu 

U

 

“The Maintenance Menu” on

page 110

Waste Ink Counter 

U

 

“Waste Ink Counter” on

page 77

SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series     User's Guide

Maintenance

 

76

Summary of Contents for SC-S40600 Series






























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands