Epson SC-S40600 Series User Manual Download Page 10

Page: 10 / 157

AC inlet #1/AC inlet #2/AC inlet #3

Connect the power cables supplied with the printer to #1 and #2. Be sure to connect both cables.

Connect the power cable supplied with the ink unit to #3. #3 is not available for the SC-S80600 Series/SC-S60600
Series/SC-S40600 Series.

Optional port

Not available for the SC-S80600 Series/SC-S60600 Series/SC-S40600 Series. Connect the connection cable sup‐
plied with the ink unit.

LAN port

Connects the LAN cable. Use a shielded twisted pair cable (category 5 or higher).

Data lamp

The data lamp lights or flashes to indicate the network connection status and whether the printer is receiving
data.

: Connected.

Flashing

: Connected. Receiving data.

Status lamp

The color indicates the network's communication speed.

Red

: 100Base-TX

Green

: 1000Base-T

USB port

Connects the USB cable.

Inside

Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the
chapters listed in the reference sections below.

SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide

Introduction

Summary of Contents for SC-S40600 Series






























































































































































Search results

Summary of Contents for SC-S40600 Series

Reviews:

Related manuals for SC-S40600 Series

Brands by name

Popular brands

Epson SC-S40600 Series, User Manual

Search results

Summary of Contents for SC-S40600 Series

Reviews:

Related manuals for SC-S40600 Series

Brands by name

Popular brands