Epson SC-F9300 series User Manual Download Page 58

Page: 58 / 146

What You’ll Need

Ready the following items before beginning cleaning
and replacement.

When the supplied parts have been completely used,
purchase new consumables.

Prepare genuine parts when replacing ink packs or
performing maintenance.

“Options and Consumable Products” on

page 117

If your gloves have worn out, prepare commercially
available nitrile gloves.

Protective eyeglasses (available in the market)

Protects your eyes from ink and ink cleaner.

Mask (available in the market)

Protects your nose and mouth from ink and ink cleaner.

Set of maintenance tools (supplied with the printer)

For general cleaning.

The following accessories are in the set.

Clean-room wipers (x100)

Tweezers (x1)

Maintenance Kit (supplied with the printer)

Use these when wiping up ink stains.

The following accessories are in the kit.

Ink cleaner (x1)

Cup (x1)

Gloves (x12)

Cleaning stick (x25)

How to use these

“Using the ink cleaner” on

page 60

A metal tray (supplied with the printer)

Use when putting cleaning utensils, removed
consumables, or ink cleaner moved in the container
supplied with the printer.

Soft cloth (available in the market)

Use when cleaning inside the front cover. Use
material that is not likely to generate lint or static
electricity.

Grease kit (supplied with the printer)

Use when applying grease to the carriage rod.

The following accessories are in the set.

Gloves (x16)

Grease tool (x1)

Cleaning sticks (x8)

Pad A (x16)

Pad B (x16)

Grease (x2)

SC-F9300 Series User's Guide

Maintenance

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands