Epson SC-F9300 series User Manual Download Page 20 | Manualshive

Page: 20 / 146

background image

❏

Do not remove the ink tanks.
Adjustments are done to the ink tanks when they
are installed. Removing them may impair quality
and performance.

❏

Store ink packs at room temperature in a location
that is not exposed to direct sunlight.

❏

To ensure print quality, use all the ink in the tank
before the earlier of the following dates:

❏

Expiry date noted on the ink pack

❏

25 days after the ink tank was refilled

❏

Ink packs that have been stored at low
temperatures for an extended period should be
allowed to return to room temperature over a
period of four hours before use.

❏

When refilling the ink tank with ink, get all the
ink out of the ink pack so that there is none
remaining.

❏

Immediately refill the ink tank once the ink pack
is open.

❏

Do not place anything on the ink tanks or subject
the ink tank to strong impacts. The ink tank could
become detached.
If the ink tank has come off, contact your dealer
or Epson Support.

Handling Media

Note the following when handling or storing media.
Media that are in poor condition will not produce
good quality prints.

Be sure to read the documentation provided with each
type of media.

Notes on Handling

❏

Do not fold the media or damage the printable
surface.

❏

Do not touch the printable surface. Moisture and
oils from your hands can affect print quality.

❏

When handling media, hold it by both edges. We
recommend wearing cotton gloves.

❏

Keep the media dry.

❏

Packaging materials can be used to store media
and should not be thrown away.

❏

Avoid locations that are subject to direct sunlight,
excessive heat, or humidity.

❏

When not in use, media should be removed from
the printer, rewound, and inserted in its original
packaging for storage. Leaving media in the
printer for extended periods may cause it to
deteriorate.

Handling Media After Printing

To maintain long lasting, high quality print results,
note the following points.

❏

Do not rub or scratch the printed surface. If they
are rubbed or scratched, the ink may peel off.

❏

Do not touch the printed surface, as this may
remove the ink.

❏

Make sure printouts are completely dry before
folding or stacking, If the printouts are stacked or
taken up without being dried sufficiently, the
print surface may be damaged.

❏

Avoid direct sunlight.

❏

To prevent discoloration, display and store prints
as instructed in the documentation supplied with
the media.

SC-F9300 Series User's Guide

Introduction

20

«
...
18
19
20
21
22
...
»

Summary of Contents for SC-F9300 series



















































































































































Reviews:

No comments

Related manuals for SC-F9300 series

Brand: Calistair Pages: 44

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Coronis 5MP Mammo

Brand: Barco Pages: 4

Brand: Barco Pages: 167

Color Coronis 2MP

Brand: Barco Pages: 156

Color Coronis 2MP

Brand: Barco Pages: 12

Brand: Barco Pages: 39

Brand: Barco Pages: 158

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: Ognibene Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands