Epson SC-F10000 Series User Manual Download Page 184

Page: 184 / 222

Others

Product

Part number

Explanation

Cleaning Kit
(except for SC-F10080H/
SC-F10080)

C13S210103

The following consumable items are included in one
maintenance set.

❏

Cleaning fluid (x1)

❏

Cup (x1)

❏

Gloves (x16)

❏

Cleaning stick (x50)

Cleaning Kit
(for SC-F10080H/SC-F10080)

C13S210104

Wiper Roll
(except for SC-F10080H/
SC-F10080)

C13S210065

Identical to the Wiper Roll supplied with the printer.

Wiper Roll
(for SC-F10080H/SC-F10080)

C13S210066

Waste Ink Bottle
(except for SC-F10080H/
SC-F10080)

C13S210071

Identical to the Waste Ink Bottle supplied with the printer.

Waste Ink Bottle
(for SC-F10080H/SC-F10080)

C13S210072

Take Up Media Holder

(except for SC-F10080H/
SC-F10080)

C12C933881

Identical to the media holder of Auto Take-up Reel Unit for
this printer.

Take Up Media Holder
(for SC-F10080H/SC-F10080)

C12C933891

Take In Media Holder

(except for SC-F10080H/
SC-F10080)

C12C933901

Identical to the media holder of Media Feeding Unit for this
printer.

Take In Media Holder
(for SC-F10080H/SC-F10080)

C12C933911

Media Cleaner Brush

C12C936031

Identical to the Media Cleaner Brush supplied with the
printer.

Presser Roller Spacer

C12C936041

Identical to the Presser Roller Spacer supplied with the
printer.

* Contact your Epson sales representative for availability.

SC-F10000H Series/SC-F10000 Series User's Guide

Appendix

184

Summary of Contents for SC-F10000 Series































































































































































































































Search results

Summary of Contents for SC-F10000 Series

Reviews:

Related manuals for SC-F10000 Series

Brands by name

Popular brands

Epson SC-F10000 Series, User Manual

Search results

Summary of Contents for SC-F10000 Series

Reviews:

Related manuals for SC-F10000 Series

Brands by name

Popular brands