Epson SC-F10000 Series User Manual Download Page 167 | Manualshive

Page: 167 / 222

background image

Item

Parameter

Explanation

Rewind Tension

Normally, use the default setting values. The higher the value, the greater
the tension.

If creases appear in the media while printing, we recommend setting a
smaller value. Do the same settings if ink adheres to the back of the media
that is being rewound.

If thick media cannot be rewound correctly, we recommend setting a
larger value.

300x600dpi -1.1pass

Lv1 to Lv9

300x600dpi -1.5pass

Lv1 to Lv9

300x600dpi -2.1pass

Lv1 to Lv9

300x600dpi -3.1pass

Lv1 to Lv9

600x600dpi -2.1pass

Lv1 to Lv9

600x600dpi -2.5pass

Lv1 to Lv9

600x600dpi -3.1pass

Lv1 to Lv9

600x600dpi -4.3pass

Lv1 to Lv9

600x1200dpi
-5.0pass

Lv1 to Lv9

600x1200dpi
-5.0pass HD

Lv1 to Lv9

1200x1200dpi
-9.0pass HD

Lv1 to Lv9

Print Quality Adjust‐
ment Limitation Tem‐
perature

0 to 50 ˚C
(32 to 122 ˚F)

Set the temperature difference at which print quality adjustment is not
executed. If the difference in room temperature and the temperature
around the print head is higher than the set value, a message indicating
the temperature is not appropriate appears on the control panel screen,
and print quality adjustment is not done. Adjust the temperature of the
room before executing print quality adjustment. To ensure the colors you
want to print, maintain a constant room temperature of 18 to 28 ˚C (64.4 to
82.4 ˚F).

Maintenance menu

The Maintenance menu can be accessed directly by pressing

.

* indicates default settings.

SC-F10000H Series/SC-F10000 Series User's Guide

Control Panel Menu

167

«
...
165
166
167
168
169
...
»

Summary of Contents for SC-F10000 Series































































































































































































































Reviews:

No comments

Related manuals for SC-F10000 Series

Brand: Canon Pages: 11

Brand: Canon Pages: 2

Brand: Canon Pages: 12

PIXMA Pro9000 Mark II Series

Brand: Canon Pages: 4

imagePROGRAF W8400

Brand: Canon Pages: 24

Super G3 FAX Board-T1

Brand: Canon Pages: 16

imagePROGRAF TZ-30000

Brand: Canon Pages: 66

imagePROGRAF W7200

Brand: Canon Pages: 126

imagePROGRAFi iPF840 series

Brand: Canon Pages: 149

Brand: Canon Pages: 166

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 2

iP4000 - PIXMA Photo Printer

Brand: Canon Pages: 3

Brand: Canon Pages: 21

Brand: Olympus Pages: 3

BW Remote Operators Software Kit-A1

Brand: Canon Pages: 20

imageRUNNER 2420

Brand: Canon Pages: 30

Brand: Canon Pages: 51

imageCLASS LBP325dn

Brand: Canon Pages: 252

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands