Epson S1C17602 Technical Manual Download Page 59 | Manualshive

Page: 59 / 368

background image

6 inTeRRuPT COnTROlleR (iTC)

S1C17624/604/622/602/621 TeChniCal Manual

Seiko epson Corporation

6-7

• When data is written to the ITC_LV0 to ITC_LV9 registers, the “Reserved” bits must always be

written as 0 and not 1.

interrupt level Setup Register

x

(iTC_lV

x

)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

interrupt level
Setup Register

x

(iTC_lV

x

)

0x4306

|

0x4318

(16 bits)

D15–11 –

reserved

–

–

–

0 when being read.

D10–8 ilV

n

[2:0]

INTn

(1, 3, ... 19) interrupt level

0 to 7

0x0 R/W

D7–3 –

reserved

–

–

–

0 when being read.

D2–0 ilV

n

[2:0]

INTn

(0, 2, ... 18) interrupt level

0 to 7

0x0 R/W

D[15:11], D[7:3]

Reserved

D[10:8], D[2:0]

ilV

n

[2:0]:

INTn

interrupt level Bits (

n

= 0–19)

Sets the interrupt level (0 to 7) of each interrupt. (Default: 0x0)

The S1C17 Core does not accept interrupts with a level set lower than the PSR IL value.

The ITC uses the interrupt level when multiple interrupt requests occur simultaneously.

If multiple interrupt requests enabled by the interrupt enable bit occur simultaneously, the ITC sends the
interrupt request with the highest level set by the ITC_LV

x

registers (0x4306 to 0x4318) to the S1C17

Core.

If multiple interrupt requests with the same interrupt level occur simultaneously, the interrupt with the
lowest vector number is processed first.

The other interrupts are held until all interrupts of higher priority have been accepted by the S1C17
Core.

If an interrupt requests of higher priority occurs while the ITC outputs an interrupt request signal to the
S1C17 Core (before acceptance by the S1C17 Core), the ITC alters the vector number and interrupt
level signals to the setting details of the most recent interrupt. The immediately preceding interrupt is
held.

7.2 Interrupt Level Bits

Table 6.

Register

Bit

interrupt

ITC_LV0(0x4306)

ILV0[2:0] (D[2:0])

P0 port interrupt

ILV1[2:0] (D[10:8])

P1 port interrupt

ITC_LV1(0x4308)

ILV2[2:0] (D[2:0])

Stopwatch timer (SWT) interrupt

ILV3[2:0] (D[10:8])

Clock timer (CT) interrupt / Real-time clock (RTC) interrupt
(S1C17624/604)

ITC_LV2(0x430a)

ILV4[2:0] (D[2:0])

8-bit OSC1 timer (T8OSC1) interrupt

ILV5[2:0] (D[10:8])

Supply voltage detector (SVD) interrupt

ITC_LV3(0x430c)

ILV6[2:0] (D[2:0])

LCD driver (LCD) interrupt / 16-bit PWM timer (T16A2) Ch.0
interrupt (S1C17624/604)

ILV7[2:0] (D[10:8])

16-bit PWM timer (T16E) Ch.0 interrupt

ITC_LV4(0x430e)

ILV8[2:0] (D[2:0])

8-bit timer (T8F) Ch.0 & Ch.1 interrupt

ILV9[2:0] (D[10:8])

16-bit timer (T16) Ch.0 interrupt

ITC_LV5(0x4310)

ILV10[2:0] (D[2:0])

16-bit timer (T16) Ch.1 interrupt

ILV11[2:0] (D[10:8])

16-bit timer (T16) Ch.2 interrupt

ITC_LV6(0x4312)

ILV12[2:0] (D[2:0])

UART Ch.0 interrupt

ILV13[2:0] (D[10:8])

I

2

C slave (I2CS) interrupt / UART Ch.1 interrupt

ITC_LV7(0x4314)

ILV14[2:0] (D[2:0])

SPI Ch.0 interrupt

ILV15[2:0] (D[10:8])

I

2

C master (I2CM) interrupt

ITC_LV8(0x4316)

ILV16[2:0] (D[2:0])

IR remote controller (REMC) interrupt

ILV17[2:0] (D[10:8])

16-bit PWM timer (T16A2) Ch.1 interrupt (S1C17624/604)

ITC_LV9(0x4318)

ILV18[2:0] (D[2:0])

A/D converter (ADC10) interrupt

ILV19[2:0] (D[10:8])

R/F converter (RFC) interrupt

«
...
57
58
59
60
61
...
»

Summary of Contents for S1C17602

















































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C17602

SmarTemp Control fx

Brand: Webasto Pages: 8

Brand: Danfoss Pages: 14

Kade KZ-700-U/H

Brand: ATT Holding Pages: 12

NetLinx Integrated Controller NI-3100

Brand: AMX Pages: 2

Brand: Samson Pages: 24

Brand: YOKOGAWA Pages: 10

Raspberry Pi 3B+ UniFi Controller

Brand: Ubiquiti Pages: 4

Brand: VRG Controls Pages: 39

Brand: C.A.P. Pages: 2

DIGITAL TIMER CONTROL

Brand: Truma Pages: 66

Brand: Hague Pages: 12

Brand: function Innovation & Technology AS Pages: 36

Brand: Hyster Pages: 25

SynchMaster 46112

Brand: Dantel Pages: 22

BD9B305QUZ-EVK-001

Brand: Rohm Pages: 9

MAGPOWR Spyder-Plus

Brand: Maxcess Pages: 60

Brand: OMC Pages: 12

Brand: ICP DAS USA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands