manualshive.com logo in svg

Epson S1C17602, Technical Manual, Page: 184 / 368

Share
Download
Epson S1C17602 Technical Manual Download Page 184

17  WaTChDOG TiMeR (WDT)

17-2

 

Seiko epson Corporation 

S1C17624/604/622/602/621 TeChniCal Manual

WDT Reset

17.3.3  

To reset WDT, write 1 to WDTRST/WDT_CTL register.
A location should be provided for periodically processing the routine for resetting WDT before an NMI or reset 
is generated when using WDT. Process this routine within 131,072/f

OSC1

 second (4 seconds when f

OSC1

 = 32.768 

kHz) cycle.
After resetting, WDT starts counting with a new NMI/Reset generation cycle.
If WDT is not reset within the NMI/Reset generation cycle for any reason, the CPU is switched to interrupt pro-
cessing by NMI or reset, the interrupt vector is read out, and the interrupt handler routine is executed. The reset and 
NMI vector addresses are TTBR + 0x0 and TTBR + 0x08.

If the counter overflows and generates an NMI without WDT being reset, WDTST/WDT_ST register is set to 1. 
This bit is provided to confirm that WDT was the source of the NMI. The WDTST set to 1 is cleared to 0 by reset-
ting WDT.

Operations in halT and SleeP Modes

17.3.4  

halT mode

 

The WDT module operates in HALT mode, as the clock is supplied. HALT mode is therefore cleared by an NMI or 
reset if it continues for more than the NMI/reset generation cycle. To disable WDT while in HALT mode, stop WDT 
by writing 0b1010 to WDTRUN[3:0]/WDT_CTL register before executing the 

halt

 instruction. Reset WDT before 

resuming operations after HALT mode is cleared.

SleeP mode

 

The clock supplied from the CLG module is stopped in SLEEP mode, which also stops WDT. To prevent generation 
of an unnecessary NMI or reset after clearing SLEEP mode, reset WDT before executing the 

slp

 instruction. WDT 

should also be stopped as required using WDTRUN[3:0].

Control Register Details

17.4  

Table 17.4.1  List of WDT Registers

address

Register name

Function

0x5040

WDT_CTL

Watchdog Timer Control Register

Resets and starts/stops the timer.

0x5041

WDT_ST

Watchdog Timer Status Register

Sets the timer mode and indicates NMI status.

The WDT registers are described in detail below. These are 8-bit registers.

note:  When data is written to the registers, the “Reserved” bits must always be written as 0 and not 1.

Watchdog Timer Control Register (WDT_CTl)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

Watchdog 
Timer Control 
Register
(WDT_CTl)

0x5040

(8 bits)

D7–5 –

reserved

–

–

–

0 when being read.

D4

WDTRST

Watchdog timer reset

1 Reset

0 Ignored

0

W

D3–0 WDTRun[3:0] Watchdog timer run/stop control

 

Other than 1010

Run

1010

Stop

1010 R/W

D[7:5] 

Reserved

D4 

WDTRST: Watchdog Timer Reset Bit

 

Resets WDT.

 

1 (W): 

Reset

 

0 (W): 

Ignored

 

0 (R): 

Always 0 when read (default)

note:  To use WDT, it must be reset by writing 1 to this bit within the NMI/reset generation cycle (4 

seconds when f

OSC1

 = 32.768 kHz). This resets the up-counter to 0 and starts counting with a 

new NMI/reset generation cycle.

Summary of Contents for S1C17602

















































































































































































































































































































































































Reviews:

No comments