Epson S1C17602 Technical Manual Download Page 155

Page: 155 / 368

13 16-BiT PWM TiMeRS (T16a2)

13-12

Seiko epson Corporation

S1C17624/604/622/602/621 TeChniCal Manual

notes: • Reset the interrupt flag before enabling interrupts with the interrupt enable bit to prevent oc-

currence of unwanted interrupt. The interrupt flag is reset by writing 1.

• After an interrupt occurs, the interrupt flag in the T16A2 module must be reset in the interrupt

handler routine.

Control Register Details

13.8

8.1 List of T16A2 Registers

Table 13.

address

Register name

Function

0x5068

T16A_CLK0

T16A Clock Control Register Ch.0

Controls the T16A2 Ch.0 clock.

0x5069

T16A_CLK1

T16A Clock Control Register Ch.1

Controls the T16A2 Ch.1 clock.

0x5400

T16A_CTL0

T16A Counter Ch.0 Control Register

Controls the counter.

0x5402

T16A_TC0

T16A Counter Ch.0 Data Register

Counter data

0x5404

T16A_CCCTL0 T16A Comparator/Capture Ch.0 Control Register

Controls the comparator/capture block and TOUT.

0x5406

T16A_CCA0

T16A Compare/Capture Ch.0 A Data Register

Compare A/capture A data

0x5408

T16A_CCB0

T16A Compare/Capture Ch.0 B Data Register

Compare B/capture B data

0x540a

T16A_IEN0

T16A Compare/Capture Ch.0 Interrupt Enable Register Enables/disables interrupts.

0x540c

T16A_IFLG0

T16A Compare/Capture Ch.0 Interrupt Flag Register

Displays/sets interrupt occurrence status.

0x5420

T16A_CTL1

T16A Counter Ch.1 Control Register

Controls the counter.

0x5422

T16A_TC1

T16A Counter Ch.1 Data Register

Counter data

0x5424

T16A_CCCTL1 T16A Comparator/Capture Ch.1 Control Register

Controls the comparator/capture block and TOUT.

0x5426

T16A_CCA1

T16A Compare/Capture Ch.1 A Data Register

Compare A/capture A data

0x5428

T16A_CCB1

T16A Compare/Capture Ch.1 B Data Register

Compare B/capture B data

0x542a

T16A_IEN1

T16A Compare/Capture Ch.1 Interrupt Enable Register Enables/disables interrupts.

0x542c

T16A_IFLG1

T16A Compare/Capture Ch.1 Interrupt Flag Register

Displays/sets interrupt occurrence status.

The T16A2 registers are described in detail below.

note: When data is written to the registers, the “Reserved” bits must always be written as 0 and not 1.

T16a Clock Control Register Ch.

(T16a_ClK

)

Register name address

Bit

name

Function

Setting

init. R/W

Remarks

T16a Clock
Control Register
Ch.

(T16a_ClK

)

0x5068
0x5069

(8 bits)

D7–4 ClKDiV

[3:0]

Clock division ratio select

CLKDIV[3:0]

Division ratio

0x0 R/W

OSC3 or

IOSC

OSC1

0xf

0xe

0xd

0xc

0xb

0xa

0x9

0x8

0x7

0x6

0x5

0x4

0x3

0x2

0x1

0x0

–

1/16384

1/8192

1/4096

1/2048

1/1024

1/512

1/256

1/128

1/64

1/32

1/16

1/8

1/4

1/2

1/1

–

1/256

1/128

1/64

1/32

1/16

1/8

1/4

1/2

1/1

D3–2 ClKSRC

[1:0]

Clock source select

CLKSRC[1:0]

Clock source

0x0 R/W

0x3
0x2
0x1
0x0

External clock

OSC3
OSC1

IOSC

MulTiMD

Multi-comparator/capture mode
select

1 Multi

0 Normal

R/W T16A_CLK0

–

reserved

–

T16A_CLK1
0 when being read.

ClKen

Count clock enable

1 Enable

0 Disable

R/W

D[7:4]

ClKDiV[3:0]: Clock Division Ratio Select Bits

Selects the division ratio for generating the count clock when an internal clock (IOSC, OSC3, or OSC1)
is used.

Summary of Contents for S1C17602

















































































































































































































































































































































































Search results

Summary of Contents for S1C17602

Reviews:

Epson S1C17602, Technical Manual, Page: 155 / 368

Search results

Summary of Contents for S1C17602

Reviews: