manualshive.com logo in svg

Epson RX595 - Stylus Photo Color Inkjet, Service Manual, Page: 54 / 131

Share
Download
Epson RX595 - Stylus Photo Color Inkjet Service Manual Download Page 54

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Troubleshooting

Troubleshooting When There is No Error Display

54

3.3.2  Power Supply Related Troubleshooting

If the printer does not operate at all (LED does not light up) even with the power turned ON, refer to the following table and perform troubleshooting.

3.3.3  Ink Supply Related Troubleshooting

†

Printer stops during initialization or printing.

Table 3-9.  Power Supply Related Troubleshooting

Cause

Check Point

Remedy

Defective power cord

Connect the normal power cord.

Replace the power cord.

Abnormal AC power 
voltage

Check the AC power voltage.

Supply the normal power.

Faulty connection of the 
connector

Check the connection between the Power Supply Board 
~ Main Board (CN3).

Correct the connection.

Fuse blown

Check the fuse (F1) on the Power Supply Board.

Replace the Power Supply Board with a new one.

Abnormal output voltage of 
Power Supply Board

Check the output voltage of the Power Supply Board.

When the output voltage is normal: Replace the Main Board with a new one.
When the output voltage is abnormal: Replace the Power Supply Board with a new one.

Table 3-10.  Troubleshooting for Printer Stop During Initialization or Printing 

Condition

Cause

Check Point

Remedy

Ink End error is 
displayed.

Ink is out.

Check to see if ink is remaining in all the ink cartridges. Replace the ink cartridge.

No Ink Cartridge error 
is displayed.

Not all the ink cartridges 
have been installed.

Check to see if all the ink cartridges have been installed 
in the I/C holders.

Install all the ink cartridges.

Check to see if no ink cartridge is in a raised position.

Install the ink cartridge properly.

The front or back hook of an ink cartridge is broken.

Replace the ink cartridge.

Ink Cartridge Trouble 
error is displayed.

Ink cartridge is damaged.

Check to see if the CSIC Board is not dislocated.

Replace the ink cartridge.

Check to see if no chip on the CSIC Board is chipping. Replace the ink cartridge.

Summary of Contents for RX595 - Stylus Photo Color Inkjet




































































































































Reviews:

No comments