Epson R800 - Stylus Photo Color Inkjet Printer Page 10 Service Manual Download

Page: 10 / 76

EPSON Stylus Photo R800

Revision A

PRODUCT DESCRIPTION

Functions

1.3 Functions

1.3.1 Control Panel

The appearance of the control panel is shown below.

Figure 1-2. Control Panel Appearance

1.3.2 Switches

Power switch

Paper switch

Ink switch

Roll paper switch

1.3.3 Indicators

Power LED

: Green

Paper LED

: Red

Ink LED

: Red

1.3.4 Switch Functions

FUNCTIONS IN NORMAL STATUS

Note : When the printer has frozen, hold down the Power switch and Ink switch for 7

seconds to forcibly switch power off.

FUNCTION AT POWER-ON

Note "*1": Status printings prints firmware version, ink counter and nozzle check

patterns.

Roll paper switch

Ink switch

Paper switch

Power switch

Ink LED

Paper LED

Power LED

Table 1-2. Normal-status Functions

Switch

Function

Power switch

• Power On/Off

Paper switch

• Loads or Ejects the Paper.

• In the condition of printing, cancel the print job.

Ink switch

• Starts the Cleaning of head with 3 second pushing.

• Moves the Carriage to ink cartridge change position.

• When Carriage is on the ink cartridge change position, return

carriage from ink cartridge change position.

Roll paper
switch

• Loads the Roll paper.

• Back out the roll paper with 3 second pushing.

• Move to tear off position / Return from tear off position.

• When the cutter is set, cuts the paper.

• When the photo album is used, ejects the paper forwards only.

(At this mode, the printer can't move the cutter and can't move
backwards.)

Table 1-3. Power-on Function

Switch

Function

Paper switch

Starts status printings.*

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

Summary of Contents for R800 - Stylus Photo Color Inkjet Printer













































































Search results

Summary of Contents for R800 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R800 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands

Epson R800 - Stylus Photo Color Inkjet Printer, Service Manual

Search results

Summary of Contents for R800 - Stylus Photo Color Inkjet Printer

Reviews:

Related manuals for R800 - Stylus Photo Color Inkjet Printer

Brands by name

Popular brands