manualshive.com logo in svg

Epson PriorityFAX 3000, Owner'S Manual, Page: 63 / 122

Share
Download
Epson PriorityFAX 3000 Owner'S Manual Download Page 63

PriorityFax 3000 Manual

Printing 

a one-touch

telephone number list

To register a number to dial out on a PBX or an international

access code, 

enter the 

number or 

code, 

press 

PAUSE, 

and then

enter the telephone number. The pause appears as a P in the

display. For example, if your telephone system requires you to dial

9 before 

dialing a 

number, 

you could enter the following: 9 PAUSE

5551212. The following would appear on the LCD TL1:9P5551212

Write the name corresponding to the one-touch number beside

the 

button 

to the left of the keypad. Press NEXT. Now your

display shows TL2. Repeat the steps above for up to four more

one-touch numbers.

When you are through registering one-touch numbers, press SET

three times to return to the date/time 

display.

To check your work or for reference, you can print a list of the one-

touch numbers you have registered by performing the following

steps:

Make sure nodocument is in the machine.

Press FUNCTION.

Press 2.

Press the # cursor key until you see the following 

display:

PRINT

TEL ONE TOUCH #

Press 

START. The list begins 

printing.

3-8

Summary of Contents for PriorityFAX 3000



























































































































Reviews:

No comments