manualshive.com logo in svg

Epson PriorityFAX 3000, Owner'S Manual, Page: 58 / 122

Share
Download
Epson PriorityFAX 3000 Owner'S Manual Download Page 58

Using the PriorityFax as a Telephone

MUTE. 

Pressing this button when you are in the middle of a

telephone call silences your conversation momentarily. Press

MUTE 

again to reenter the conversation. Hanging up the handset

when MUTE is on breaks the telephone connection.

HOLD. Pressing this button 

stops the transmission of sound to

and from the other party. The connection is not broken even if

the handset is returned to the telephone cradle while HOLD is
on. 

Resume transmission 

by pressing the HOLD 

button again or

removing the handset from the cradle (if so positioned).

PAUSE. 

You can use this button in registering one-touch

telephone numbers, as described later in this chapter.

FLASH. 

You can use this button for special telephone company

features you may have installed, such as call waiting.

Note

Call waiting is discouraged for use with this fax machine

because it may interfere with fax transmission and

reception.

FUNCTION. 

You can use this button in registering one-touch

telephone numbers, as described later in this chapter.

ONE-TOUCH. 

Each 

button 

allows you to dial a complete pre-

registered telephone or fax 

number.

3-3

Summary of Contents for PriorityFAX 3000



























































































































Reviews:

No comments