manualshive.com logo in svg

Epson PriorityFAX 3000, Owner'S Manual, Page: 57 / 122

Share
Download
Epson PriorityFAX 3000 Owner'S Manual Download Page 57

PriorityFax 3000 Manual

The four buttons to the right of the keypad and just below the

Liquid Crystal Display (LCD) are used (from left to right) as

follows:

Before dialing, the buttons 

function as

SPKR (Speaker), REDIAL, and S. DIAL (Speed Dial).

After you dial, the four buttons function as

CALL RSRV (Call 

Reservation, 

used 

for faxing only), 

MUTE,

HOLD, 

and 

FLASH.

After the FUNCTION button 

has been pressed, the buttons act as

NEXT, SET, 

and 

PAUSE.

Buttons are discussed below only as they relate to telephone

operations. For information on button use for fax operations, see

chapter2

KEYPAD. 

The keypad is used to dial telephone numbers, speed

dial numbers, and for registering one-touch numbers.

SPKR 

(speaker). Pressing this button allows you to dial a

telephone number without lifting the handset.

Note

The PriorityFax is not a speaker phone. You cannot speak

to someone on the 

other end of 

a call 

without lifting the

handset.

REDIAL 

Pressing this button dials the most recent number called.

3-2

Summary of Contents for PriorityFAX 3000



























































































































Reviews:

No comments