Epson PERFECTION V10 Service Manual Download | Manualshive

Page: 38 / 77

background image

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of Main Unit

38

5. Disconnect CN1, CN2, CN4, CN7 connectors, and CN5 for the V350 Photo, and

CN8 for the Perfection V100 Photo/V200 Photo to remove the Main Board.

Figure 4-12. Removing the Main Board (Perfection V100 Photo/V200 Photo/V350 Photo)

Figure 4-13. Removing the Main Board (Perfection V10)

When reassembling the Upper Main Board Shield Plate, match
the guide pin and the positioning hole, and insert the plate
under the Lower Main Board Shield Plate.

For the Perfection V100 Photo/V200 Photo/V350 Photo, make
sure to screw the Upper Main Board Shield Plate together with
the earth cable of the Harness TPU/Harness AFL.

When reassembling the Upper Main Board Shield Plate, be
careful not to get the CR Motor cable caught under the plate.

Figure 4-11. Reassembling the Upper Main Board Shield Plate

Guide pin and

positioning hole

C.B.P. 3x8

Upper Main Board Shield Plate

Insert position

C H E C K

P O I N T

Perfection V10 is equipped with a different Main Board to
Perfection V100 Photo/V350 Photo, therefore note that the number
of connectors differ.

CN1

CN2

CN4

CN7

CN5

CN8

CN4

CN7

CN1

CN2

«
...
36
37
38
39
40
...
»

Summary of Contents for PERFECTION V10














































































Reviews:

No comments

Related manuals for PERFECTION V10

Brand: 4DDynamics Pages: 2

Brand: Radio Shack Pages: 40

Brand: Keithley Pages: 81

Brand: Virbac Pages: 2

Brand: Kodak Pages: 50

Brand: Colortrac Pages: 10

Brand: Plustek Pages: 2

MobileOffice H100

Brand: Plustek Pages: 2

Brand: Hasselblad Pages: 20

Pannoramic SCAN II 2.0

Brand: 3DHISTECH Ltd. Pages: 142

Brand: HandHeld Pages: 11

Book Executive 3

Brand: IRIScan Pages: 18

Brand: IRIScan Pages: 26

Paragon 1200A3Pro

Brand: Mustek Pages: 38

PageExpress 4800 Pro

Brand: Mustek Pages: 58

Brand: UMAX Data Systems Pages: 48

Brand: tau Pages: 2

Brand: NCR Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands