Epson Perfection 636 Page 70 Reference Manual Download

Page: 70 / 79

Specifications

Page 70

Auto Document Feeder Specifications

Basic Specifications

Dimensions

Width: 12.6 inches (319 mm)
Depth: 17.8 (451 mm)
Height: 5.4 inches (137 mm)

Weight

4.9 lbs (2.2 kg)

Feeder type

Sheet through, face up loading, face down ejecting, roller friction

Loading position

Left side of document against left side of feeder, opposite scanner’s
original point

Scanning speed

3 pages per minute (A4, line art, 300 dpi, draft mode)

Connector

8-pin DIN male

Environmental
temperatures

Operation: 50 °F to 90 °F (10 °C to 32 °C)
Storage:

–4 °F to 140 °F(–20 °C to 60 °C)

Humidity (without
condensation)

Operation: 20% to 80%
Storage:

10% to 85%

Operating
conditions

Ordinary office or home conditions; avoid extreme dust, operation under
direct sunlight, and strong light sources.

Reliability

Load/eject: MCBF 20,000 sheets
Hinge: MCBF 12,000 cycles

Electrical

Input voltage: DC 24V±10%
DC 5V±5%
Input current: 24V: 0.8 A
5V: 0.2 A

ref.book Page 70 Monday, September 28, 1998 4:24 PM

Summary of Contents for Perfection 636
















































































Search results

Summary of Contents for Perfection 636

Reviews:

Related manuals for Perfection 636

Brands by name

Popular brands

Epson Perfection 636, Reference Manual

Search results

Summary of Contents for Perfection 636

Reviews:

Related manuals for Perfection 636

Brands by name

Popular brands