Epson OmniLink TM-T70-i Technical Reference Manual Download Page 76

Page: 76 / 120

EPSON TMNet WebConfig

EPSON TMNe

WebCo

s a U

o se

he prod

a web browser.

s sec

descr

bes EPSON TMNe

WebCo

ing

Explorer as a browser.

Starting EPSON TMNet WebConfig

he s

eps below

o s

p EPSON TMNe

WebCo

Start up a PC connected to the network.

Start up the web browser, and input the following.

Whe

SSL

s d

sabled: h

p://[Th

s prod

's IP address]/webco

Whe

SSL

s e

abled: h

ps://[Th

s prod

's IP address]/webco

EPSON TMNe

WebCo

Help Screen Display

ck [Help]

o d

splay

he help scree

for EPSON TMNe

WebCo

Version Screen Display

ck [Abo

]

o d

splay

he vers

scree

for EPSON TMNe

WebCo



For the product’s IP address, see the status sheet. For the status sheet, see

"Con-

firming with a status sheet" on page 47



A user name and a password will be required on the authentication screen. Enter
“epson” for both the user name and the password. You can change the password on
the [Password Setting] screen (see

"Admin Settings - Administrator Information -

Password" on page 94

.).

Summary of Contents for OmniLink TM-T70-i

























































































































Search results

Summary of Contents for OmniLink TM-T70-i

Reviews:

Related manuals for OmniLink TM-T70-i

Brands by name

Popular brands

Epson OmniLink TM-T70-i, Technical Reference Manual

Search results

Summary of Contents for OmniLink TM-T70-i

Reviews:

Related manuals for OmniLink TM-T70-i

Brands by name

Popular brands