Epson LX-1170 Service Manual Download

Page: 87 / 129

LX-300+/1170

Revision C

Disassembly and Assembly

4.2.7.11 Paper Feed Mechanism Disassembly

Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)

Remove the PF motor assembly. (See 4.2.7.10 "PF Motor Assembly Removal".)

Remove the release lever.

Figure4-23. Release Lever Removal

Release the hook of the right frame securing the gear, 27.5 and remove the gear, plain
washer 5.2x0.3x10 and the compression spring, 1.18.

Remove the combination gear, 8.5, 25.2 from the right frame.

Figure4-24. Paper Feed Mechanism Disassembly

C H E C K

P O I N T

When installing the release lever, be sure to align the marking on the
release lever with the marking on the release shaft.

Release shaft

Release lever

Hook at the right frame

Combination gear, 8.5, 25.2

Combination spring, 1.18

Plain washer, 5.2 x 0.3 x 10

Gear, 27.5

Summary of Contents for LX-1170


































































































































Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands

Epson LX-1170, Service Manual

Search results

Summary of Contents for LX-1170

Reviews:

Related manuals for LX-1170

Brands by name

Popular brands