Epson LQ-570e User Manual Download

Page: 68 / 248

2-24

Printing on Continuous Paper

13. After you finish printing, open the paper guide cover; then

tear off the printed document at the perforation nearest the
paper exit slot.

To remove the paper from the tractor, follow the steps under
“Removing the paper from the pull tractor” on page 2-21.

Removing the pull tractor

To remove the tractor from the pull position, follow these steps:

1. Remove any paper loaded on the pull tractor as described on

“Removing the paper from the pull tractor” on page 2-21.

2. Turn off the printer. Then remove the printer cover and lift

the paper guide up and off the printer.

3. Press the tractor’s lock tabs, tilt the tractor toward you, and

lift it off the printer.

Summary of Contents for LQ-570e

























































































































































































































































Search results

Summary of Contents for LQ-570e

Reviews:

Related manuals for LQ-570e

Brands by name

Popular brands

Epson LQ-570e, User Manual

Search results

Summary of Contents for LQ-570e

Reviews:

Related manuals for LQ-570e

Brands by name

Popular brands