Epson LQ-570e User Manual Download

Page: 25 / 248

Setting Up the Printer

1-1

Chapter 1

Setting Up the Printer

Unpacking the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Choosing a Place for the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Positioning the continuous paper supply. . . . . . . . . . . . . . . . 1-4

Installing or Replacing the Ribbon Cartridge . . . . . . . . . . . . . . . . . 1-5

Attaching the Paper Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Plugging in the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Connecting the Printer to Your Computer . . . . . . . . . . . . . . . . . . . 1-14

Installing the Printer Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16

Installing the printer software in Windows 95, 98,
or NT 4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Installing the printer software in Windows 3.1
or NT 3.5x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
For DOS programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19

Summary of Contents for LQ-570e

























































































































































































































































Search results

Summary of Contents for LQ-570e

Reviews:

Related manuals for LQ-570e

Brands by name

Popular brands

Epson LQ-570e, User Manual

Search results

Summary of Contents for LQ-570e

Reviews:

Related manuals for LQ-570e

Brands by name

Popular brands