Epson LQ-570e User Manual Download | Manualshive

Page: 22 / 248

background image

12

Getting to Know Your Printer

For United Kingdom Users

Use of options

Epson (UK) Limited shall not be liable against any damages
or problems arising from the use of any options or consumable
products other than those designated as Original EPSON
Products or EPSON Approved Products by Epson (UK) Limited.

Safety information

w

Warning:

This appliance must be earthed. Refer to the rating plate for
voltage and check that the appliance voltage corresponds to the
supply voltage.

Important: The wires in the mains lead fitted to this appliance
are coloured in accordance with the following code:

Green and yellow — Earth
Blue — Neutral
Brown — Live

If you have to fit a plug:

As the colours of the mains lead of this appliance may not match
coloured markings used to identify the terminals in a plug, please
proceed as follows:

The green and yellow wire must be connected to the terminal in
the plug which is marked with the letter E or the Earth symbol (

G

).

The blue wire must be connected to the terminal in the plug
marked with the letter N.

The brown wire must be connected to the terminal in the plug
marked with the letter L.

«
...
20
21
22
23
24
...
»

Summary of Contents for LQ-570e

























































































































































































































































Reviews:

No comments

Related manuals for LQ-570e

Brand: IBM Pages: 112

Brand: DataCard Pages: 2

AdvancedPunch Pro

Brand: GBC Pages: 92

Brand: Canon Pages: 198

Brand: Oki Pages: 62

Brand: TallyGenicom Pages: 144

7300DX - Phaser Color Laser Printer

Brand: Xerox Pages: 14

VersaCamm SP-300V

Brand: Roland Pages: 4

Brand: Xiamen Hanin Electronic Technology Pages: 62

Brand: Parkside Pages: 176

Brand: Oki Pages: 80

Brand: Oki Pages: 107

Brand: Oki Pages: 143

8200DX - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 2

Brand: Oki Pages: 45

Brand: Kyocera Pages: 24

Brand: Oki Pages: 32

bizhub press c1060

Brand: Konica Minolta Pages: 159

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands