manualshive.com logo in svg

Epson LQ-570e, User Manual

The Epson LQ-570e is a reliable dot matrix printer designed for high-speed printing. It guarantees crisp, clear text documents and graphics. Enhance your printing experience by downloading the user manual from manualshive.com for free. This comprehensive manual provides step-by-step instructions to optimize your printer's performance and functionality.

Share
Download
background image

A-22      

Enhancing Your Printer With Options

To remove the roll paper holder, carefully lift up the printer and 
pull out the roll paper holder from beneath the printer.

Loading roll paper

After you install the roll paper holder, follow the steps below to 
load a roll of paper,

1. Make sure the printer is turned off. Open the paper guide 

cover and remove the paper guide.

2. Make sure the paper tension unit is installed.

3. Set the paper thickness lever (located under the printer cover) 

to the proper position for the thickness of your roll paper.

4. Set the paper release lever to the single-sheet position.

5. Cut the leading edge of the roll paper straight across.

6. Insert the roll paper holder shaft into the center of the paper 

roll as shown.

Summary of Contents for LQ-570e

























































































































































































































































Reviews:

No comments

Related manuals for LQ-570e

Saxxot CRU-158 Operation Manual preview
CRU-158
Brand: Saxxot Pages: 13
DataCard SP75 Plus Product Manual preview
SP75 Plus
Brand: DataCard Pages: 25
Xerox VersaLink B415 User Manual preview
VersaLink B415
Brand: Xerox Pages: 324
iDPRT iMOVE T3Pro User Manual preview
iMOVE T3Pro
Brand: iDPRT Pages: 74
Memjet AS-1180C Service Manual preview
AS-1180C
Brand: Memjet Pages: 181
Oki MPS730b Manual De L'Utilisateur preview
MPS730b
Brand: Oki Pages: 143
LulzBot TAZ 6 Operation Manual preview
TAZ 6
Brand: LulzBot Pages: 3
RAYSHAPE Edge E1 User Manual preview
Edge E1
Brand: RAYSHAPE Pages: 41
Copystar CS-C3225E Specifications preview
CS-C3225E
Brand: Copystar Pages: 1
CraftUnique CraftBot PlusPro Quick Start Manual preview
CraftBot PlusPro
Brand: CraftUnique Pages: 2
Lexmark CX510 series Product Specifications preview
CX510 series
Brand: Lexmark Pages: 2
3D Systems ProJet 126C User Manual preview
ProJet 126C
Brand: 3D Systems Pages: 72
Canon iR-ADV Security Kit-B1 Service Manual preview
iR-ADV Security Kit-B1
Brand: Canon Pages: 35
Canon Duplex Unit-A1 Service Manual preview
Duplex Unit-A1
Brand: Canon Pages: 50
Canon High Capacity Stacker-G1 Operation Manual preview
High Capacity Stacker-G1
Brand: Canon Pages: 49
Canon iP5000 - PIXMA Color Inkjet Printer Quick Start Manual preview
iP5000 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 100
Canon iR Security Kit-A2 Installation Procedure preview
iR Security Kit-A2
Brand: Canon Pages: 49
Canon IPF600 Service Manual preview
IPF600
Brand: Canon Pages: 16

Brands by name

Popular brands

Load more brands