background image

64

Paper Handling

Adjusting the top-of-form position

The top-of-form position is the position on the page where the 
printer starts printing. If your printing appears too high or low 
on the page, you can use the Micro Adjust function to adjust the 
top-of-form position.

Follow these steps to adjust the top-of-form position:

c

Caution:
Never use the knob to adjust the top-of-form position; this may 
damage the printer or cause it to lose the top-of-form position.

Note:

Your top-of-form position setting remains in effect until you change 
it, even if you turn off the printer.

The top margin setting made in some application software overrides 
the top-of-form position setting you make with the Micro Adjust 
function. If necessary, adjust the top-of-form position in your 
software.

1. Make sure the printer is turned on.

2. Load paper. (If the tractor is in a push position, press the 

Load/Eject

 button to advance continuous paper to the 

current top-of-form position.) If necessary, lift up the printer 
cover so you can see the paper position.

3. Hold down the 

Pause

 button for about three seconds. The 

Pause

 light starts flashing and the printer enters the Micro 

Adjust mode.

Summary of Contents for LQ-2090

























































































































































































































































Reviews: