manualshive.com logo in svg

Epson LQ-2090, Reference Manual

Share
Download
Epson LQ-2090 Reference Manual Download Page 53

Paper Handling

45

2

2

2

2

2

2

2

2

2

2

2

2

Using the Tear-off Function

If the push tractor is installed, you can use the tear-off function to 
advance your continuous paper to the printer’s tear-off edge 
when you finish printing. You can then easily tear off the printed 
document. When you resume printing, the printer automatically 
feeds the paper back to the top-of-form position so that you can 
save the paper normally lost between documents.

Removing continuous paper

You can remove continuous paper using the tear-off function in 
two ways: manually by pressing the printer’s 

Tear Off/Bin

 button 

or automatically by turning on auto tear-off mode. The 

Tear 

Off/Bin

 light flashes when the paper is in the tear-off position.

If the perforation between pages is not aligned with the tear-off 
edge, you can adjust the position of the perforation using the 
Micro Adjust function. See “Adjusting the tear-off position” on 
page 61 for more information.

c

Caution:

❏

Never use the tear-off function with the pull tractor; the paper 
may come off the pull tractor and jam the printer. After you 
finish printing, tear off the printed document at the 
perforation nearest the paper exit slot.

❏

Never use the tear-off function to feed continuous paper with 
labels backward; they may come off their backing sheet and 
jam the printer.

Using the Tear Off/Bin button

Follow these steps to remove continuous paper using the 

Tear 

Off/Bin

 button:

1. After the printer finishes printing your document, check that 

the 

Tear Off/Bin

 light is not flashing.

Summary of Contents for LQ-2090

























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands