Start Here
12
Raise the control panel, then press the power button to
turn on the product.
Note:
If an error message appears, turn off the product and
check that no protective material has been left inside the
product.
13
Select your language, country, date, and time.
Note:
You can change these settings later using the
product’s control panel. For more information, see the
online User’s Guide.
Follow steps 14 and 15 to continue ink charging.
14
When the message to see the
Start Here
sheet appears
on the LCD screen, press and hold the help button for
5 seconds.
15
When the ink confirmation message appears on the LCD
screen, select
Done
to start charging the ink. Ink charging
takes approximately 10 minutes.
Caution:
Do not unplug or turn off the product, raise the
scanner unit, or load paper while the product is charging
or you’ll waste ink.
Note:
The included ink bottles are designed for reliable
printer setup and cannot be resold. After setup, the
remaining ink is available for printing.
16
To complete filling the ink tanks, repeat steps 1 through 7
using the remaining ink in the bottles.
Note:
Replace the bottle cap before disposing of the bottles.
17
Close the ink tank cover and scanner unit.
18
Select Next and follow the on-screen instructions to reset
the ink levels.
19
Follow the on-screen instructions to adjust the print
quality.
Note:
•
You need to load paper before you can adjust the print quality.
See “Load paper” on the back of this sheet for details.
•
You can change these settings later using the product’s
control panel.
IMPORTANT:
Before using this product, make sure you read
these instructions and the safety instructions in the online
User’s
Guide
.
Important Safety Instructions:
When using telephone equipment, you
should always follow basic safety precautions to reduce the risk of fire,
electric shock, and personal injury, including the following:
• Do not use the product near water.
• Always keep this guide handy.
• Avoid using a telephone during an electrical storm. There may be a
remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
Caution:
To reduce the risk of fire, use only a No. 26 AWG or larger
telecommunication line cord.
1
Unpack
Note:
Do not open the ink bottles until you are ready to fill the ink
tanks.
1
Remove all protective materials from the product.
2
Lift up the scanner unit until it locks into place and
remove all protective materials from inside the product.
Caution:
Do not touch the flat white cable or the ink tubes and
their translucent cover.
2
Fill ink tanks
Warning:
Keep the ink bottles out of the reach of children and
do not drink the ink.
Caution:
This product requires careful handling of ink. If ink spills,
wipe it off immediately with a damp towel to avoid permanent stains.
If ink gets on your clothes or belongings, it may not come off.
Note:
•
Use the ink bottles included with the printer to set up the product.
Part of the ink will be used to charge the print head.
1
Make sure that the transportation lock is in the down position.
2
Open the ink tank cover, then open the cap for the black ink.
3
Unpack the black (BK) ink bottle. Hold the ink bottle upright
and slowly turn the bottle cap to remove it.
Remove filling cap off and remove protective foil from
bottle. Put filling cap on the bottle by slowly turning the
cap until it is tightly secured.
Caution:
Do not shake or squeeze the ink bottles. Do not touch
the top of the ink bottle after its cap is removed.
4
Insert the ink bottle into the filling port.
Note:
Do not force the bottles into position;Remember
Black ink to be used on BK tank and on CMY tanks.
5
Wait for the ink to fill the tank.
Do not squeeze the bottle.
Note:
Ink flows into the tank and
stops automatically when the ink is
filled to the upper line. If ink does
not flow from the bottle, lift and
reinsert the bottle.
Caution:
After setup, periodically
inspect the ink level to ensure it
is not below the lowest line on
the tank. Prolonged use when
ink is below the lowest line could
damage the product. See the
online User’s Guide for refilling
instructions.
6
When the ink tank is full, remove the ink
bottle and securely close it with the cap.
Place the remaining ink aside; you will
need
it later.
Note:
Do not leave the ink bottle inserted;
otherwise
the bottle may be damaged or ink
may
leak.
7
Close the ink tank cap.
8
Repeat the previous steps for the other colors.
9
Close the ink tank cover.
10
Lift the scanner unit up slightly and lower it. When
the scanner unit catches, lift it up again and lower it
completely.
11
Connect the power cord to the back of the product and to
an electrical outlet.
Caution:
Do not connect to your computer yet.
GO ET
-15000 SP
Note:
Black ink to be filled in BK and CMY tanks.
