manualshive.com logo in svg

Epson EpsonNet C82391, Administrator'S Manual, Page: 93 / 299

Share
Download
Epson EpsonNet C82391 Administrator'S Manual Download Page 93

4

Settings for NetWare      

4-47

Instructions for Using a Dial-Up Network

This section explains about using a dial-up network.

Note:

The primary server described in this manual indicates a primary time 
server which offers time to the workstations on the network.

Using a dial-up network in each mode

Print Server mode

You must use a dedicated dial-up line.
Since polling is performed on the file server in the print server 
mode, no vicarious response by the router is possible. 
Therefore, no dial-up connection is possible in this case. 

Remote Printer mode

In Remote Printer mode, use of a router with a vicarious 
response function allows the primary server to be installed at 
the dial-up destination. However, an extra account might be 
generated when the primary server is down. To avoid that, it 
is recommend to use connections via a dedicated dial-up line.

Follow the instructions for using a dial-up line.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Reviews:

No comments