Epson EpsonNet C82391 Administrator'S Manual Download Page 35

Page: 35 / 299

Setting the IP Address

3-1

Chapter 3

Setting the IP Address

To use the interface card with TCP/IP, you need to assign it an IP
address using EpsonNet WinAssist, EpsonNet MacAssist, or the
arp/ping commands.

The IP address must be set in the following cases:

❏

When configuring the interface card using EpsonNet
WebAssist (the utility pre-installed on the interface card)

❏

When using remote (LPR on IP) printing from NetWare 5.x

❏

When using TCP/IP (via EpsonNet Direct Print) printing
from Windows Me/98/95/2000/NT 4.0

❏

When using TCP/IP (LPR port) printing from
Windows 2000/NT 4.0/NT 3.51

❏

When using TCP/IP (lpr port) printing from OS/2 Warp or
UNIX

❏

When using Internet Printing with EpsonNet Internet Print
from Windows 98/95/NT 4.0

❏

When using Internet Printing from Windows Me/2000

❏

When managing printers using EpsonNet WebManager via
TCP/IP

Summary of Contents for EpsonNet C82391












































































































































































































































































































Search results

Summary of Contents for EpsonNet C82391

Reviews:

Epson EpsonNet C82391, Administrator'S Manual, Page: 35 / 299

Search results

Summary of Contents for EpsonNet C82391

Reviews: