manualshive.com logo in svg

Epson EpsonNet C82391, Administrator'S Manual, Page: 30 / 299

Share
Download
Epson EpsonNet C82391 Administrator'S Manual Download Page 30

2-2      

Easy Setup Configuration

Starting Easy Setup from the CD-ROM

Follow the steps below to start EpsonNet WinAssist Easy Setup 
from the CD-ROM.

1. Insert the software CD in the CD-ROM drive.

2. The EPSON Installation Program starts automatically.

If the EPSON Installation Program does not start 
automatically, click 

Start

 and then 

Run

. Type 

D:\EPSETUP

 

and click 

OK

. (Substitute the appropriate letter for your CD-

ROM drive if necessary.)

3. Double-click 

Run EpsonNet WinAssist Easy Setup

.

The EpsonNet WinAssist Easy Setup dialog box appears. 
Click 

Next

.

4. Read the Usage Agreement and click 

Next

.

5. Select the target printer and click 

Next

.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Reviews:

No comments