Epson EpsonNet C82391 Page 291 Administrator'S Manual Download

Page: 291 / 299

Installing Protocols

A-13

Windows NT 3.51

Note:

Be sure that

Workstation

is in the Installed Network Software list.

1. Double-click the

Network

icon in Control Panels to display

the Network Settings dialog box. Make sure that the NetBEUI
Protocol is in the Installed Network Software list.

2. If

NetBEUI Protocol

is not in the list, click

Add Software

Select

NetBEUI Protocol

from the Network Software pull-

down menu, and click

Continue

to add NetBEUI.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands

Epson EpsonNet C82391, Administrator'S Manual

Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands