Epson EpsonNet C82391 Page 238 Administrator'S Manual Download

Page: 238 / 299

12-30

EPSON Status Monitor 2 (Windows only)

Uninstalling EPSON Status Monitor 2

You can remove EPSON Status Monitor 2 from your computer in
the following manner:

Caution:

Quit other programs such as virus check programs before
removing EPSON Status Monitor 2.

Note for Windows 2000, NT 4.0, and NT 3.51:

You need to log on as an Administrator.

From Windows Me/98/95/2000/NT 4.0

1. Close EPSON Status Monitor 2 as described in “Stopping

Monitoring” on page 12-28.

2. Click

Start

on the taskbar, point to

Settings

, and then click

Control Panel

3. Double-click

Add/Remove Programs

4. Click

EPSON Status Monitor 2

and click the

Add/Remove

button (Windows Me/98/95/NT 4.0) or the

Change/

Remove

button (Windows 2000).

5. Follow the instructions on the screen.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands

Epson EpsonNet C82391, Administrator'S Manual

Search results

Summary of Contents for EpsonNet C82391

Reviews:

Related manuals for EpsonNet C82391

Brands by name

Popular brands