Epson EpsonNet C82391 Page 227 Administrator'S Manual Download | Manualshive

Page: 227 / 299

background image

12

EPSON Status Monitor 2 (Windows only)

12-19

Note for Windows 2000, NT 4.0, and NT 3.51:

You need to log on as a Network Administrator to use this feature.

Note:

Delete printers that appear in this list but are not always connected to
the network and printers that the Status Monitor cannot get status
information about, because they unnecessarily use system resources. To
delete a printer, select the printer and click

Delete Printer

on the

Settings menu.

Adding uninstalled network printers

Before you start monitoring uninstalled network printers, you
need to add them to the Uninstalled Network Printers list. Follow
these steps:

1. Click the Uninstalled Network Printers list.

2. Click

Add Printer

on the Settings menu.

«
...
225
226
227
228
229
...
»

Summary of Contents for EpsonNet C82391












































































































































































































































































































Reviews:

No comments

Related manuals for EpsonNet C82391

Brand: Oki Pages: 40

Brand: Xerox Pages: 310

Brand: Gateway Pages: 138

UniServer R4900 G5

Brand: H3C Pages: 141

275C - SRP Two-color Dot-matrix Printer

Brand: BIXOLON Pages: 100

Brand: Lucent Technologies Pages: 85

Brand: EFI Pages: 4

Brand: Tally Pages: 174

PRICOM PRICOM C- 5100

Brand: Silex technology Pages: 7

Brand: Magicard Pages: 31

Brand: QUANTA Pages: 177

Brand: Olivetti Pages: 26

Brand: Ice Pages: 133

Brand: Boundless Pages: 33

Brand: D-Link Pages: 40

9500 - HL 1660EN B/W Laser Printer

Brand: Brother Pages: 258

Brand: D-Link Pages: 113

Brand: D-Link Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands