manualshive.com logo in svg

Epson EpsonNet C82391, Administrator'S Manual

Share
Download
Epson EpsonNet C82391 Administrator'S Manual Download Page 197

11

EpsonNet Direct Print Utility      

11-3

Setting Up Your Printer

When setting up a printer to print with LPR, you can add both a 
printer located in the same segment and one located beyond a 
router.

Note:

❏

Be sure that the computer is connected to the network and TCP/IP 
is correctly set.

❏

The valid IP address other than default value "192.168.192.168" 
must be set; otherwise the printer does not appear under the 
Epson_lpr group icon. See Chapter 2 or 3 to set the IP address.

❏

The EPSON Status Monitor 2 utility shipped with the interface card 
models C82362

✽

/C82363

✽

/C82364

✽

 with software version 1.x 

and EPL-N2700/N4000 printers enables EPSON TCP/IP printers. 
These EPSON TCP/IP printers can coexist with lpr printers added 
by EpsonNet Direct Print.

❏

The job control functions such as 

Cancel Printing

 and 

Purge 

Print Jobs

 are available when you double-click the target printer 

icon in the Printers folder. However, if the printer has already 
started printing a document, the print job may not be cancelled 
completely.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands