Epson EpsonNet C82391 Administrator'S Manual Download Page 143

Page: 143 / 299

Settings for Macintosh

7-9

Configuring for AppleTalk Using EpsonNet WebAssist

You can use EpsonNet WebAssist after setting the IP address of
the interface card, as described in Chapter 2.

Note:

❏

A web browser must be installed in your computer.

❏

TCP/IP must be correctly set for the computer and the interface card.

❏

Do not operate EpsonNet WinAssist/MacAssist and EpsonNet
WebAssist for the printer at the same time.

❏

There are some restrictions on the characters you can use depending
on your browser. For details, see your browser or OS manual.

1. Turn on the printer with the interface card.

2. Run EpsonNet WebAssist by either method described below.

❏

Run EpsonNet WinAssist or EpsonNet MacAssist. Select
the printer that you want to configure from the list and
click

Launch Browser

❏

Open your browser, and type in the IP address of the
interface card directly. Do not run EpsonNet WinAssist
or MacAssist.

http:

IP address of interface card

Summary of Contents for EpsonNet C82391












































































































































































































































































































Search results

Summary of Contents for EpsonNet C82391

Reviews:

Brands by name

Popular brands

Epson EpsonNet C82391, Administrator'S Manual

Search results

Summary of Contents for EpsonNet C82391

Reviews:

Brands by name

Popular brands