manualshive.com logo in svg

Epson EpsonNet C82391, Administrator'S Manual, Page: 135 / 299

Share
Download
Epson EpsonNet C82391 Administrator'S Manual Download Page 135

7

Settings for Macintosh      

7-1

Chapter 7

Settings for Macintosh

This chapter explains how to configure the interface card for 
TCP/IP or AppleTalk in a Macintosh environment using 
EpsonNet MacAssist or WinAssist.

Supported systems

The supported systems are as follows:

❏

Macintosh OS
Mac OS 9.x, 8.x, 7.6.x 
System 7.5.x

❏

Apple network driver
AppleTalk Driver 58.x (EtherTalk Phase II)
OpenTransport 1.0.8, 1.1 or later (EtherTalk Phase II)

❏

Apple LaserWriter 8 printer driver

❏

EPSON printer driver

❏

EPSONScript driver 
EPSONScript Driver, EPSONScript Utility

Note: 

When using a Macintosh with a interface card, do not use EPSON 
Namer. Use EpsonNet WinAssist/MacAssist/WebAssist to change the 
printer name.

Summary of Contents for EpsonNet C82391












































































































































































































































































































Reviews:

No comments