manualshive.com logo in svg

Epson EpsonNet C82391, Administrator'S Manual, Page: 102 / 299

Share
Download
Epson EpsonNet C82391 Administrator'S Manual Download Page 102

5-6      

Settings for Windows Me/98/95

6. Enter your password (up to 20 characters) and click 

OK

 to 

save settings. If you are entering a password for the first time, 
click 

Change

 and set the password. For more information 

about passwords, see “About passwords” on page 10-7. 

Follow the on-screen instructions. After updating is complete, 
refresh the configuration by selecting 

Refresh

 from the View 

menu.

 

c

Caution:

Since it takes 2 or 3 minutes to send new settings to the 
interface card, you must wait until the on-screen message 
appears before turning off your printer.

Configuring for NetBEUI using EpsonNet WebAssist

Note:

❏

A web browser must be installed in your computer.

❏

TCP/IP must be correctly set for the computer and the interface card.

❏

Do not operate EpsonNet WinAssist and EpsonNet WebAssist for 
the printer at the same time. 

❏

There are some restrictions on the characters you can use depending 
on your browser. For details, see your browser or OS 
documentation.

1. Turn on the printer with the interface card.

2. Run EpsonNet WebAssist by either of the methods described 

below.

❏

Run EpsonNet WinAssist. Click the printer you want to 
configure from the list and click 

Launch Browser

.

❏

Open your browser, and type in the IP address of the 
interface card directly. Do not run EpsonNet WinAssist.

http:

//

IP address of interface card

/

Summary of Contents for EpsonNet C82391












































































































































































































































































































Reviews:

No comments