Epson EL 33 User Manual Download

Page: 75 / 115

Removing a Drive from the Upper Drive Bay

To remove a drive from the upper drive bay, follow these steps:

1. Remove both the ribbon cable connector and the power

cable connector from the drive.

Remove the screws securing the drive.

3. Reach behind the drive and gently push it to the front of the

bay; then pull it out of the slot.

4. Once you have removed the drive, replace the faceplate by

inserting one side of the plate, then gently guiding the other

side into place. You will hear it snap into place.

Post-installation Procedures

After you install or remove your drive(s) and replace the cover

on your computer, you need to run the SETUP program to

define the correct configuration for your newly-installed drive.

See Chapter 1 for instructions.

installing and Removing Drives

4-17

Summary of Contents for EL 33




















































































































Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands

Epson EL 33, User Manual

Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands