Epson EL 33 User Manual Download

Page: 69 / 115

Removing a Hard Disk Drive From the Internal
Drive Bay

To remove a hard disk drive, reverse the installation steps

outlined above. Then disconnect the hard disk drive ribbon

cable and the power supply cable from the back of the drive.

When you disconnect the cables, grasp the connectors and pull

them straight out so you do not bend the pins; do not pull on

the cables. Use the screw to again secure the hard disk drive

mounting bracket to the base of the computer.

Installing a Drive in the Upper Horizontal Drive Bay

Your system comes with a 3.25-inch diskette drive installed in

the lower horizontal drive bay. You can also install a diskette

drive, a CD-ROM, a tape drive, or a second hard disk drive in

the upper horizontal drive bay. If you install a second hard disk

drive in this bay, make sure you purchase the appropriate cable

to connect both drives to the hard disk drive connector.

Before you install a drive in the upper drive bay, remove the

cover. Once you have the drive installed, replace the cover,

following the instructions in Chapter 3.

installing and Removing Dives

4-11

Summary of Contents for EL 33




















































































































Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands

Epson EL 33, User Manual

Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands