Epson EL 33 User Manual Download

Page: 27 / 115

Defining your own drive type

If the parameters for your hard disk (listed in its

documentation) do not match any of the types listed in the table

above, you can define your own type. Follow these steps:

Move your cursor to

Hard Disk 1

or 2 and press + or -

until you see drive type 48 or type 49.

Press to move the cursor to the

Cyl

field.

Type the appropriate cylinder value for your hard disk. The

documentation that came with your hard disk drive will

provide the appropriate information.

Continue pressing to move the cursor to the next field and

type in the appropriate values.

If you are installing Epson-supplied drives, use the information

in the following table to define your drive type.

Epson-supplied hard disk drive types

Actual formatted size may be slightly different than size on drive label.

Note

If you are going to install NetWare 286, version 2.2, you

cannot assign a user-defined drive type for your drive

without installing NetWare IDE drivers. You can obtain

these drivers (IDE.DSK and IDE.OBJ) by downloading

IDE286.ZIP from Netwire in CompuServe®. Alternatively,

you can select one of the pre-defined hard disk drive types

that most closely matches the drive you are installing.

1-14

Setting Up Your System

Summary of Contents for EL 33




















































































































Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands

Epson EL 33, User Manual

Search results

Summary of Contents for EL 33

Reviews:

Related manuals for EL 33

Brands by name

Popular brands