Epson EB-421i User Manual Download Page 27 | Manualshive

Page: 27 / 155

Epson EB-421i User Manual Download Page 27

Attention

•

If you use a USB hub, operation may not be performed correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.

•

When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.

•

Connect a digital camera or hard disk to the projector using a USB cable supplied with or specified for use with the device.

Removing USB devices

After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from
the projector.

Connecting a microphone

You can output microphone audio from the projector's speaker by connecting a commercially available dynamic microphone.

a

•

Plug-in-power is not supported.

•

Adjust

Mic Input Level

if the microphone audio is difficult to hear, or if it is too loud resulting in a crackling sound.

s

Settings

-

Mic Input Level

•

Make the following settings to output audio from a microphone when the projector is turned off.
Set

Standby Mode

to

A/V Standby

.

s

Extended

-

Standby Setup

-

Standby Mode

Set

Standby Microphone

to

On

.

s

Extended

-

Standby Setup

-

Standby Microphone

Connecting Equipment

27

«
...
25
26
27
28
29
...
»

Summary of Contents for EB-421i




























































































































































Reviews:

No comments