Epson EB-421i User Manual Download Page 142

Page: 142 / 155

Supported Resolutions

Computer signals (analog RGB)

Signal

Refresh Rate (Hz)

Resolution (dots)

VGA

60/72/75/85

640x480

SVGA

56/60/72/75/85

800x600

XGA

60/70/75/85

1024x768

WXGA

1280x768

1366x768

60/75/85

1280x800

WXGA+

60/75/85

1440x900

SXGA

70/75/85

1152x864

60/75/85

1280x1024

60/75/85

1280x960

SXGA+

60/75

1400x1050

UXGA

1600x1200

WXGA++

1600x900

WSXGA+

1, 2

1680x1050

MAC13”

640x480

MAC16”

832x624

MAC19”

1024x768

Signal

Refresh Rate (Hz)

Resolution (dots)

MAC21”

1152x870

1 EB-436Wi/EB-426Wi only

2 Only compatible when

Wide

is selected as the

Resolution

from the

Configuration menu.

Images may also be projected when signals other than the above are input.
However, some functions may be limited.

Component Video

Signal

Refresh Rate (Hz)

Resolution (dots)

SDTV (480i)

720x480

SDTV (576i)

720x576

SDTV (480p)

720x480

SDTV (576p)

720x576

HDTV (720p)

50/60

1280x720

HDTV (1080i)

50/60

1920x1080

Composite video

Signal

Refresh Rate (Hz)

Resolution (dots)

TV (NTSC)

720x480

TV (SECAM)

720x576

TV (PAL)

50/60

720x576

Input signal from the HDMI port

Signal

Refresh Rate (Hz)

Resolution (dots)

VGA

640x480

Supported Monitor Displays

142

Summary of Contents for EB-421i




























































































































































Search results

Summary of Contents for EB-421i

Reviews:

Brands by name

Popular brands

Epson EB-421i, User Manual

Search results

Summary of Contents for EB-421i

Reviews:

Brands by name

Popular brands