manualshive.com logo in svg

Epson C31C514452, Technical Reference Manual

Share
Download
Epson C31C514452 Technical Reference Manual Download Page 72

3-30

   Setup

Rev. H

3.4.7.4  Ethernet interface

The following view shows the part names of the UB-E01.

Before connecting any of the cables, make sure that both the printer and the host computer are 
turned off.

1. Make sure both the printer and the host computer are turned off.

2. Plug the 10BASE-T cable connector securely into the UB-E01's 10BASE-T Ethernet connector 

until you feel it click.

CAUTION:

Do not connect a telephone line , a display module cable, or a drawer kick cable to the 
UB-E01’s 10BASE-T connector.

Note:

The display module connector on the TM printer cannot be used when the UB-E01 is installed.

3. Connect the power supply to the printer.

10BASE-T Ethernet 
interface 
connector

LED (green)   LED (red)

Be sure not to push the 
LEDs by accident

Switch 

If you press and hold 
this switch when the 
printer is on, the 
interface will be 
reset to the factory 
settings

Summary of Contents for C31C514452



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands