manualshive.com logo in svg

Epson C31C514452, Technical Reference Manual

Share
Download
Epson C31C514452 Technical Reference Manual Download Page 36

2-4

   System Planning

Rev. H

•

Logs between an application and CO (for used API and its return value)

•

Logs for device status (acquires causes for offline and errors in devices)

2.1.2.2  EPSON OPOS ADK Contents

Any installer later than EPSON OPOS ADK Ver2.10 supports the silent install function that can 
install the OPOS environment without a user interface, which offers easier installation. With this 
installer, OPOS Control for EPSON devices that are compatible with OPOS, manuals, utilities 
and sample programs described below can be installed.

❏

OPOS Control for EPSON devices

The following can be installed: CO, SO, header file for C++, header file for VB, TLB file for 
CO, or device information file.

❏

Manuals

•

User’s Guide (Environment construction manual: installation/uninstallation/usage of 
each utility)

•

Application Development Guide (for OPOS compatible application developers: editions 
for common description and for each device)

❏

Utilities

•

 SetUpPOS Utility

Can select a device to be used, connection port and settings, such as paper width, 
monochrome/two-color (only for two-color supported devices) and print waiting time.

•

TM Flash logo utility

Can register a bit map file to the printer and customer display.

•

USB device driver

Required to connect a USB specification printer.

•

Sample program

Sample programs in VB and VC++ can be installed.

Summary of Contents for C31C514452



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands