manualshive.com logo in svg

Epson AcuLaser M4000 Series, User Manual

Share
Download
Epson AcuLaser M4000 Series User Manual Download Page 80

AcuLaser M4000 Series

User's Guide

Using the Control Panel

80

Bookmark Menu

The bookmark menu appears by pressing the 

OK

 button while the LCD panel displays 

Ready

 or 

Sleep

. 

In the bookmark menu, the bookmarked setting items are listed and you can select one of them. 
The following menus are bookmarked by default.

❏

Reset Menu

❏

MP Tray Size

❏

System Information

To register the menus in bookmark, see “How to register menus as bookmarks” on page 54 for 
details.

Status and Error Messages

This section contains a list of error messages shown on the LCD panel, a brief description of each 
message and suggestions for correcting the problem. Note that not every message shown on the 
LCD panel indicates a problem. When the   mark is displayed at the right of the warning message, 
multiple warnings occur. To confirm all warnings that occur, press the 

d

Down

 button to display 

the 

Status Menu

, then press the 

r

Enter

 button. The LCD panel also displays the remaining service 

life of the imaging cartridge and available paper sizes.

Bookmark Registered

The selected menu is registered as a bookmark.

Bookmark Failed

The selected menu cannot be registered as a bookmark. Some menus cannot be registered as 
bookmarks.

Cancel All Print Job

The printer is canceling all print jobs in the printer memory, including jobs the printer is currently 
receiving or printing. This message appears when the 

+

Cancel Job

 button has been pressed 

down for more than 2 seconds.

Cancel Print Job

The printer is canceling the current print job. This message appears when the 

+

Cancel Job

 button 

has been pressed and released within 2 seconds.

Summary of Contents for AcuLaser M4000 Series


























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands