manualshive.com logo in svg

Epson AcuLaser C9300 Series, User Manual

Share
Download
Epson AcuLaser C9300 Series User Manual Download Page 155

Operational Problems

The Ready light does not turn on

Cause

What to do

The power cord may not be properly plugged into the
electrical outlet.

Turn off the printer, check the power cord connections between
the printer and the electrical outlet, then turn the printer back on.

The electrical outlet may be controlled by an outside
switch or an automatic timer.

Make sure that the switch is turned on or plug another electrical
device into the outlet to check whether the outlet is operating
properly.

The printer is in the sleep mode (the 

Wake Up/Sleep

button lights) or in the power off mode (the 

Wake Up/

Sleep

 button blinks).

Press the 

Wake Up/Sleep

 button to return the printer to ready

status.

The printer does not turn off

Cause

What to do

The printer is in the power off mode (the 

Wake Up/Sleep

button blinks).

Wait for a while. The printer turns off in approximately two
minutes.

To not enter the power off mode, set 

Power Off Timer

 to 

Off

 in

Energy Saver Menu

 on the control panel.

The printer does not print (Ready light off)

Cause

What to do

The printer is offline.

Press the 

Start/Stop

 button once to switch the printer to ready

status. Make sure that the Ready light turns on.

Some error may have occurred.

Check the LCD panel to see if an error message appears.

The printer is in the power off mode (the 

Wake Up/Sleep

button blinks).

Press the 

Wake Up/Sleep

 button to return the printer to ready

status.

To not enter the power off mode, set 

Power Off Timer

 to 

Off

 in

Energy Saver Menu

 on the control panel.

Epson AcuLaser C9300 Series     User's Guide

Troubleshooting     

155

Summary of Contents for AcuLaser C9300 Series



















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands