manualshive.com logo in svg

Epson AcuLaser C9100, Reference Manual

Share
Download
Epson AcuLaser C9100 Reference Manual Download Page 91

Using the Printer Software with Windows

91

3

3

3

3

3

3

3

3

3

3

3

3

5. Set the password for the job by entering a four-digit number 

in the password text box.

Note:

❏

Passwords must be four digits.

❏

Only numbers from 1 through 4 can be used for passwords.

❏

Keep passwords in a safe place. You must enter the correct 
password when printing a Confidential Job.

6. Click 

OK

. The printer stores the print job on the Hard Disk 

Drive. 

To print or delete this data using the printer’s control panel, see 
“Printing and Deleting Reserve Job Data” on page 340.

Monitoring Your Printer Using EPSON Status 
Monitor 3

EPSON Status Monitor 3 is a utility program that monitors your 
printer and gives you information about its current status.

Note for Windows XP users:

❏

Shared Windows XP LPR connections and shared Windows XP 
Standard TCP/IP connections with Windows clients do not support 
the Job Management function.

❏

EPSON Status Monitor 3 is not available when printing from a 
Remote Desktop connection.

Note for Windows 95 users:

Network printers can not be monitored with EPSON Status Monitor 3.

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands