manualshive.com logo in svg

Epson AcuLaser C9100, Reference Manual

Share
Download
Epson AcuLaser C9100 Reference Manual Download Page 75

Using the Printer Software with Windows

75

3

3

3

3

3

3

3

3

3

3

3

3

Printing with an overlay

Follow the steps below to print a document with overlay data.

1. Open the file to print with overlay data.

2. From the application, access the printer driver. Open the File 

menu, choose 

Print

 or 

Print Setup

, then click 

Printer

, 

Setup

, 

Options

, 

Properties

, or a combination of these buttons, 

depending on your application.

3. Click the 

Special

 tab.

4. Select the 

Form Overlay

 check box, and click 

Overlay 

Settings

 to open the Overlay Settings dialog box.

5. Choose the form from the Form drop-down list, then click 

OK

 

to return the Special menu.

6. Click 

OK

 to print the data.

1

2

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands