manualshive.com logo in svg

Epson AcuLaser C9100, Reference Manual

Share
Download
Epson AcuLaser C9100 Reference Manual Download Page 34

34

Paper Handling

Selecting a paper source

You can specify a paper source manually, or set the printer to 
select the paper source automatically.

Manual selection

You can use the printer driver or the printer’s control panel to 
select a paper source manually.
To access the printer driver, for Windows, see “Accessing the 
printer driver” on page 53, or for Macintosh, see “Accessing the 
printer driver” on page 120. 
And to use the printer’s control panel, see “Using the Control 
Panel Menus” on page 338:

❏

Using the printer driver

For Windows users:

Access the printer driver, click the 

Basic

 

Settings

 tab, and 

select the paper source that you want to use from the Paper 
Source list. Then click 

OK

.

For Macintosh users:

Access the printer driver, select 

Printer

 

Settings

 from the 

drop-down list and click the 

Basic Settings

 tab (for Mac OS 

X), or open the Basic Settings dialog box (for Mac OS 9). Then, 
select the paper source that you want to use from the Paper 
Source list and click 

OK

.

❏

Using the printer’s control panel

Access the control panel’s Setup Menu, then select 

Paper 

Source

 and specify the paper source you want to use.

Summary of Contents for AcuLaser C9100























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands