manualshive.com logo in svg

Epson AcuLaser C2000, Administrator'S Manual

Share
Download
Epson AcuLaser C2000 Administrator'S Manual Download Page 24

2-6

Connecting to the Network

❏

The Internal Print Server is set to the default IP address
"192.168.192.168". This private IP address may cause conflicts on
your network. To prevent this, you must confirm that the same IP
address does not already exist on the network before connecting the
Internal Print Server to the network. If it does, turn off the device
which has the same IP address, then change the default IP address
of the Internal Print Server.

Setting the IP Address on the Printer’s Control
Panel

After connecting the printer to the network, you need to set the
IP address for the Internal Print Server.

To set the IP address, subnet mask, and default gateway from the
control panel, follow the steps below.

1. Turn on the printer.

2. Press the

SelecType

button until

Test Menu

appears.

3. Press the

Menu

button until

Network Menu

appears.

4. Press the

Item

button to enter

Network I/F = On

.

5. Press the

Item

button to enter

Network Config = No

. Then

press the

Value

button to enter

Network Config = Yes

. Press

the

Enter

button.

6. Press the

Item

button to enter

Get IP Address = Panel

. The

following methods of acquiring the IP address are supported.

Panel:

Choose

Panel

to setting the IP address, subnet mask,

and default gateway using the printer’s control panel.

Summary of Contents for AcuLaser C2000

















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands