manualshive.com logo in svg

Epson AcuLaser C1900, Reference Manual, Page: 186 / 396

Share
Download
Epson AcuLaser C1900 Reference Manual Download Page 186

186

Installing Options

Removing the Hard Disk Drive

Perform the installation procedure in reverse.

Formatting the Hard Disk Drive

To format the Hard Disk Drive, follow the instructions below.

1. Make sure the printer is off and all interface cables are 

disconnected.

2. Hold down the 

d 

Down button while you turn on the printer.

3. When you see the message 

Support Mode

 on the LCD panel, 

select 

HDD Format

 in the support menu.

Note:

❏

After formatting the Hard Disk Drive, the printer will 
automatically reboot.

❏

When you want to erase only the fonts installed from the optional 
Adobe PostScript 3 (PS3), follow steps 1 through 3 above. Select 

PS3 HDD Init

 when the optional Adobe PostScript 3 Kit is 

installed.

❏

Other fonts installed from PS3 will also be erased.

❏

When installing a Hard Disk Drive from other products, format it 
with this function.

Memory Module

This printer has two DIMM slots, but one slot has a 32MB DIMM 
already installed in it at the time of manufacture. To increase 
printer memory to its maximum of 1 GB, you have to purchase 
two 512 MB DIMMs and remove the original 32MB DIMM.

Summary of Contents for AcuLaser C1900













































































































































































































































































































































































































Reviews:

No comments